The Hillman Group 230054 sexkantsskruv, 5/16-tum X 2-1/2-tum, zink, 100-pack 2,5 tum

Brand:The Hillman Group

3.7/5

83.49

Effektiv lagerkontroll på ett ögonkast, Akro-Mils tvåfärgade Indicator Bin är ett enfacks Kanban-system med en färgad triggersida för att indikera lågt lager och förhindra lager-out och löpande bandavbrott. Får aldrig slut på lager. Har du dessa problem: anställda vet inte vad de ska göra när lagret är lågt eller tar slut, arbetare som använder olika sätt att meddela arbetsledare om lageravbrott, inspekterar VARJE soptunna för att se efter lågt lager? Med Akro-Mils Indicator Bins ser du omedelbart när lagret är lågt. Den ljusa orange avtryckarsidan på behållaren indikerar att lagret är lågt. Fyll bara på båda sidorna av behållaren, välj lager, vänd när den blå sidan är tom, fyll på behållaren med lager, vänd tillbaka till den blå sidan och placera tillbaka på hyllan. Låt Akro-Mils Indicator Bin ta centrum i din lagerhanteringsprocess! Gjord i USA.

Insexdrivning för kontrollerad dragkraft med hylsa eller skiftnyckel. Grova gängor som kräver ett förborrat hål med minimalt spel ovanför fästelementet. Zinkfinish ger rättvist korrosion och rostskydd. Designad för att fästa föremål på trä och ankare murverk.
Country of Origin China
Domestic Shipping Item can be shipped within U.S.
Drive System External Hex
Exterior Finish Zinc
Head Style Hex
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item Dimensions LxWxH 5.4 x 4.2 x 3.3 inches
Item model number 230054
Manufacturer The Hillman Group
Material Steel
Product Dimensions 5.4 x 4.2 x 3.3 inches; 4.7 Pounds

3.7

6 Review
5 Star
79
4 Star
8
3 Star
8
2 Star
6
1 Star
0

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med*

Scritto da: Charles R
Useful Information
Good quality and great price for lags. Twist off a head here and there, which is usually my fault. If you’re experiencing more than 2-5% twisting off at the head, best check your technique before you go scowling the manufacturer. Make sure your pilot hole exceeds the seated depth of the screw by at least 1/2”. Some materials may require slightly larger diameter pilots. I set with an impact driver installing into standard 2x4, 2x6 etc lumber. My neighbors hate me. If the need arises to tighten or remove these lags, I would advise a hand ratchet and drill/driver , respectively. Further use of an impact tool after initially setting the lag could snap it.
Scritto da: Don
Use a pilot hole!
For the guy who said they were dull. Try using a pilot hole! 3/16" or 1/4" and they'll go right in. Do that consistently and the number you twist off will drop and you won't be tearing up your wood.
Scritto da: Jeff R.
They work
Great value
Scritto da: James
More than Good Enough for the Job But Great for the Money
good enough - box store quality. But they cost 1/3 the price so definitely buy unless you are building the space shuttle or something where strength and tolerance are key factors.
Scritto da: Zombiexm
Simple Screws
When you need to screw a item correctly, these lag screws do the job.
Scritto da: Bobby J. Denson
Dull
The tip is so rounded and dull that they are much harder than other brands to get started.

Relaterade produkter

Upptäck vårt internationella nätverk

Vi skickar till 28 länder, över 200 000 produkter. Håll dig uppdaterad, prenumerera på nyhetsbrevet.

Array