Eastman 24 tums vattenvärmare kontakt, 3/4 x 3/4 tum FIP, flätat rostfritt stål vattenvärmare kontaktdon, 48252

Name: Eastman 24 tums vattenvärmare kontakt, 3/4 x 3/4 tum FIP, flätat rostfritt stål vattenvärmare kontaktdon, 48252
Brand: Eastman
SKU: 0091712482529
Price: 31.97 EUR
Availability: InStock

Brand:Eastman

3.7/5

€
31.97

PRODUKTBESKRIVNING Amazon Basics 6 uttag väggmonterat överspänningsskydd FRÅN TILLVERKAREN Amazon Basics

Belopp

Lägg till i kundvagn Köp nu

EAN: 0091712482529

Kategorier Verkyg & hemförbättring, Byggnadsmaterial, HVAC, Värmare & Tillbehör,

SPECIFIKATIONER: Denna fläta av rostfritt stål har ett maximalt sprängtryck på 1200 PSI och en maximal arbetstemperatur på 221 grader F; UPC-godkänd, CSA-certifierad och följer NSF och blyfria riktlinjer för dricksvattenapplikationer. HÅLLBAR: Denna vattenvärmarslang är byggd av en giftfri PVC-kärna, en flerfilamentflätad nylonförstärkning, ett klart ytterskal av vinyl och en flätad utsida i rostfritt stål av kvalitet 304 som är designad för att förhindra veck och krympning. ENKEL INSTALLATION: Flexslangar inkluderar blyfria mässingsadaptrar för att möjliggöra lödfria anslutningar till kopparrör; kontakter möjliggör enkel installation i trånga utrymmen. VAD INGÅR: Denna flätade flexibla vattenförsörjningskontakt mäter 24 tum i längd utrustad med en 3/4 x 3/4 tums FIP-anslutning. EASTMAN VATTENVÄRMEKONTAKT: Denna Steel-Flex vattenvärmarekontakt används för att ansluta en vattenledning till en ny eller befintlig elektrisk varmvattenberedare.

Brand	Eastman
Color	Stainless
Connector Type	Adapter
Exterior Finish	Brass
Item Dimensions LxWxH	24 x 0.75 x 0.75 inches
Material	Stainless Steel
Number Of Pieces	1
Size	24 in

5 Star

4 Star

3 Star

2 Star

1 Star

Skriv din recension

Din e-post kommer inte att publiceras. Alla obligatoriska fält är markerade med^*

Ditt betyg

Scritto da: Timbo

A good hose for cheap

I read the reviews before and so was a bit concerned that the internal diameter (ID) of the hose was not going to be 1/2". My first purchase was for a thermal expansion tank connector so that wasn't of really big concern. I am happy to report that the ID of these hoses is 15/32 of an inch (0.46875") at the brass nuts and at least 1/2" internally between the two end nuts. If you need full 16/32" of water flow then you probably should go with a more expensive alternative to this hose. Given that my water heater tank's hot water out anode-nipple combo rod has a small ID and I have an old galvanized 1/2" system up stream of my cold water intake to the heater, it won't make much difference in my particular case to lose the 1/16" ID that some folks must have. I noted when inspecting the hose that the brass barrel nipple that is used to at least 1" deep on each side, so this appears to be a quality part, even if the intake and outtake brass ID is slightly smaller than spec. Will update this review if I find any significant issues when in use in our hot water home system, etc.

Scritto da: David

Solid product

These worked well for what I needed them for.

Scritto da: eperks

The inside diameter is just fine

To all those concerned that a few reviews slammed this product because the inside diameter is not 3/4", that is how most, if not all, water heater supply hoses are. The inside diameter is perfectly fine. The big stores sell hoses with the same inside diameter, you'll get plenty of water for typical residential use, & if you don't it's not because of this hose diameter. The supply lines to your bath sink, kitchen sink, tubs, and showers are not 3/4" either. People spreading stupidity.

Scritto da: Shaun B

It’s a hose what can I say

I used it when I replaced my water softener. It did the job, the quality looks decent and the price was right. It looked very similar to the hose it replaced(fluid master) not a terribly different design and that hose was 10 years old and only being replaced as a precaution.

Scritto da: Joel

Good

Good product for a good price. I had no problems with it.

Scritto da: Amazon Customer

Looks good in our water closet!

We used this to connect up a thermal expansion tank in our water closet. It curves nicely, although you do have to fiddle with the connector bearings a little if you want it to loop properly in a tight space. Since installing this cable, we ordered two more to replace the old corrugated ss flex hoses from our water pipes to our water heater. It looks a lot more aesthetically pleasing, what with all the new ss braided 3/4" cables in there now.

Scritto da: Erich Fahrner

Quality

I saw several reviews about the is smaller than they expected. Although it says 1/2 inch all others are the same issue. This is for hot water and the flex pipe itself needs a lining to accommodate its function.

Scritto da: Henry Cummings

works as expected

decent build quality

Scritto da: ROGER

Excellent item works so easily

Delivered as promised no issues works well. It's hard to find these at your big box stores for this length.

Scritto da: Kevin J.

Great quality

No complaints so far did what it supposed to do.

Scritto da: Rob D

Just what I needed

Easy connection and disconnection.

Scritto da: R Nieuwenhoven

Great

Hols water, duh...

Scritto da: Simulator

Good quality for great price

Great heavy duty hose used to connect water softener. Not a full 3/4 internal diameter, but no big issue on that for our needs. Compared to big box stores, same quality at half the price.