0
0

3M Bare - Metal Seam Sealer, 08310, beigenvärinen, kaksiosainen, roikkumaton, itsestään sekoittuva epoksi, 200 ml/6,75 fl oz patruuna epoksi beige

Brand:3M

3.8/5

91.19

3M™ Bare Metal Seam Sealer 08310 on kova, joustava tiivistemateriaali, joka on suunniteltu paljaiden metallien liitosten, kuten teräksen tai alumiinin, sekä pohjustetun tai maalatun metallin tiivistämiseen törmäyskorjauksessa. Kaksiosainen, itsestään sekoittuva epoksitiiviste voidaan helposti tiivistää, työstää tai harjata saumoihin, ja se kovettuu vain 15 minuutissa. Siinä on neutraali beige väri. Käytä 3M™ Performance Manual Applicator 08117:n, 3M™ Manual Patruunaapplikaattorin 08571 tai 3M™ Performance Pneumatic Applicator 09930 (myydään erikseen) kanssa. Kovettumisaika: 1 tunti Käsittelyaika: 1-10 minuuttia Työaika: 10 minuuttia Maalausaika: 15 minuuttia

Vain teolliseen/ammatilliseen käyttöön. Ei kuluttajamyyntiin tai -käyttöön. NEUTRAALI BEIGE: Väri voi vähentää maalausmateriaalia ja aikaa. NOPEA ASETUS: Kovettuu vain 15 minuutissa, mikä tehostaa myymäläaikaa. RASKAS-BODY FORMULA: Vuotamaton puhtaaseen ja tehokkaaseen työkaluun pysty- ja vaakasaumoissa. ERITYISESTI MUOTOITTU: Ei kutistumista, halkeilua tai kaasun muodostumista. KAKSIOSINEN EPOKSI: Tiivistysaine muodostaa kestävän, joustavan tiivisteen paljaille metallisaumoille.
Brand 3M
Color Beige
Country of Origin USA
Department unisex-adult
Is Discontinued By Manufacturer No
Item model number 08310
Item Weight 6.75 Ounces
Manufacturer 3M
Material Epoxy
Product Dimensions 12 x 9.63 x 5.38 inches; 6.75 Ounces
Style Epoxy

3.8

8 Review
5 Star
86
4 Star
7
3 Star
3
2 Star
1
1 Star
3

Kirjoita arvostelusi

Sähköpostiasi ei julkaista. Kaikki pakolliset kentät on merkitty*

Scritto da: john g.
as described
good price fast delivery
Scritto da: XDAEDAEX
Does the job
Worked its purpose
Scritto da: snatch
Great product if used correctly
I used this for sealing drip rails on a Ranger... very pleased with the results. It does self level quickly and evenly and looks great. I used about 1/2 of the 200ml tube for both sides and probably put in quite a bit more than the factory did...but one tube would easily do both drip rails on a full size truck I think. Since it is self levelling you must dam up the ends with masking tape and make sure the surface itself is level... and plan to grind out some of it on the ends, easily done with a small file. Overnight cure is better, the data sheet says paintable within a short period but it was still a bit tacky after an hour... rock hard the next day and very easy to finish the ends.
Scritto da: Jan
Very "epoxy" like. It's an epoxy after-all
Not sure about self-leveling, was expecting something more "fluidy", the viscosity and stickiness is just like honey and as a matter of fact - as epoxy :). It's likely great glue for gluing separate pieces, but not great for filling voids, due to low viscosity and high stickiness. The nozzle with the cartridge is bulky and exponentially grows with the gun, so not great for tight spaces. The proprietary gun is another story for itself... Should have gone with a smaller package with a thumb applicator instead...
Scritto da: chad caro
Great product
Worked as it should
Scritto da: Max Power
Bought to replace seam sealer on the drip rails of ...
Bought to replace seam sealer on the drip rails of a 71 Chevy pickup. Make sure you level the vehicle - mask off areas you don't want this stuff on and PEEL off the tape ASAP before it sets up or it is there forever (and trying to peel it from under sealer will result in sealer getting pulled up as well). You cannot use this on vertical sections as it flows for at least five minutes before it begins to set up. Ended up buying the heavy bodied seam sealer (3M 8303) to do the vertical sections first (along with a few spots on the firewall & cowl) then used the 08307 for the level areas (came out glass smooth). Wear gloves - it is messy if you are not careful.
Scritto da: Max Power
Bought to replace seam sealer on the drip rails of ...
Bought to replace seam sealer on the drip rails of a 71 Chevy pickup. Make sure you level the vehicle - mask off areas you don't want this stuff on and PEEL off the tape ASAP before it sets up or it is there forever (and trying to peel it from under sealer will result in sealer getting pulled up as well). You cannot use this on vertical sections as it flows for at least five minutes before it begins to set up. Ended up buying the heavy bodied seam sealer (3M 8303) to do the vertical sections first (along with a few spots on the firewall & cowl) then used the 08307 for the level areas (came out glass smooth). Wear gloves - it is messy if you are not careful.
Scritto da: Inland Classic Auto LLC
Spot on
Sticks well to bare metal. Quick drying

Liittyvät tuotteet

hot

Tutustu kansainväliseen verkostoomme

Toimitamme 28 maahan, yli 200 000 tuotetta. Pysy ajan tasalla, tilaa uutiskirje.

Array