ARRMA hammaspyörä, 20T HD Mod1 Safe-D5, ARA310967

Brand:ARRMA

3.5/5

€
43.78

Tämä luja teräksinen 20T Mod1 Safe-D hammaspyörä on täydellinen osa RC-työkalulaatikossasi. Ominaisuudet: Vahva ja kestävä teräs takaa pitkäkestoisen suorituskyvyn äärimmäisissä RC-olosuhteissa - Tarkasti valmistettu leveä hammasprofiili sujuvan toiminnan takaamiseksi - "D" muotoiltu reikä, joka sopii moottorin akselin profiiliin, joten käyttö ja jarrut eivät katoa, jos säätöruuvi peruuttaa - Sopii 5 mm:n moottorin akselin halkaisijalle - Tarkasti valmistettu kierteinen säätöruuvin reikä - E-klipsi mukana moottorin akselin hammaspyörän kiinnitykseenSisältää:1 x 20T Mod1 Safe-D hammaspyörä 1 x ruuvi - M4 x 4 mm 1 x E-klipsi - 3,2 mm

Määrä

Lisää ostoskoriin Osta nyt

EAN: 5052127035095

Luokat Remote & App Controlled Vehicles & Parts, Taajuus- ja sovellusohjatut ajoneuvojen osat, Voimalaitteet ja voimansiirtojärjestelmät, Vaihteistot ja tasauspyörästöt, Vaihteet,

ARRMA hammaspyörä, 20T HD Mod1 Safe-D5, ARA310967.

Country of Origin	China
Customer Reviews	4.4 4.4 out of 5 stars 72 ratings 4.4 out of 5 stars
Item model number	ARA310967
Item Weight	0.96 ounces
Manufacturer	ARRMA
Manufacturer recommended age	14 years and up
Product Dimensions	4 x 2.5 x 0.75 inches

5 Star

4 Star

3 Star

2 Star

1 Star

Kirjoita arvostelusi

Sähköpostiasi ei julkaista. Kaikki pakolliset kentät on merkitty^*

Arviosi

Scritto da: Scotty Bot

Safe-D design is PERFECT

Kept losing pinion gears, not anymore!

Scritto da: Sk1lZz

Bad luck, -great seller and fast shipping but….

I got this several months ago and unfortunately stuff happened and could not install right away. When I finally had a chance I discovered that the gear is warped and can’t be used. I’m sure it was just bad luck and the quality is usually good. Anyway install it straight away just in case.

Scritto da: Jamie Zempel

Great for X maxx Stock motor.

Fits with slight modifications to the motor shaft. After putting it on and orange thread locker never had the pinion “slip” again. This is a great solution if any one starts to get this issue with there x maxx motor shaft.

Scritto da: Keith

Does not fit the 8s was tricked by the c clip set up

Got this for my 8s kraton it does not say which model it was for

Scritto da: Jeffery ward

Excellent

I installed this on my infraction. The stock 15t pinion was to low geared and the inured 25t speed pinion was too much. This 20t hits that sweet spot right in the middle that gives excellent top speeds and allows extended bash sessions without overheating the electronics.

Scritto da: Amazon Customer

Perfect fit

Very well made good quality. Fits tight

Scritto da: Hilario R. Gonzales

Not the arrma 20tooth upgrade you’re looking for

Avoid if you have Thypon 3s...it doesnt fit too big...waste of time.